Dear students, as we announced, we have made available 4 boards and motors in room KN:E-2 for you to work at any time. The room is located at Karlovo namesti and is accessible whenever the university is open, which includes even weekends. The keys from the locker are available at building E reception desk. If the whole room is locked, you can ask the reception guy to open it. Currently, there are only 4 Ethernet cables available in the room - look for yellow cables at the back sides of the room. The boards will be available in the room today, until 8 PM. Tomorrow, Mr. Hubacek will bring them to H131. Starting from Sunday, the 4 boards will be again in E2. We will temporarily move them to H131 on Wednesdays for exercises. If you encounter any problems with the boards, motors etc., please let us know immediately so that we can fix the problems quickly. Best regards, -Michal Sojka
Good evening, I am at the KN:E2. The left front computer has some problems with the display. I am now on right front computer and cant connect to target. It says that there is some error on 0x100000 address. Some midam inconsistency or something like that. Tried it on: 192.168.202.48 192.168.202.51 I also found out that you must probably need to use network mask of 202 at KN:E2. Where might be problem? Thank You. Marek Laszlo On Fri, Dec 16, 2016 at 2:26 PM, Michal Sojka <sojkam1@fel.cvut.cz> wrote:
Dear students,
as we announced, we have made available 4 boards and motors in room KN:E-2 for you to work at any time. The room is located at Karlovo namesti and is accessible whenever the university is open, which includes even weekends.
The keys from the locker are available at building E reception desk. If the whole room is locked, you can ask the reception guy to open it. Currently, there are only 4 Ethernet cables available in the room - look for yellow cables at the back sides of the room.
The boards will be available in the room today, until 8 PM. Tomorrow, Mr. Hubacek will bring them to H131. Starting from Sunday, the 4 boards will be again in E2. We will temporarily move them to H131 on Wednesdays for exercises.
If you encounter any problems with the boards, motors etc., please let us know immediately so that we can fix the problems quickly.
Best regards, -Michal Sojka
_______________________________________________ PSR mailing list PSR@rtime.felk.cvut.cz https://rtime.felk.cvut.cz/mailman/listinfo/psr
What do you see on serial line/usb? Does the board boot VxWorks? 0x100000 is the address where bootloader loads the vxworks image. On 16. prosince 2016 19:04:20 CET, "Marek L." <laggersvk@gmail.com> wrote:
Good evening,
I am at the KN:E2. The left front computer has some problems with the display.
I am now on right front computer and cant connect to target. It says that there is some error on 0x100000 address. Some midam inconsistency or something like that. Tried it on: 192.168.202.48 192.168.202.51
I also found out that you must probably need to use network mask of 202 at KN:E2.
Where might be problem?
Thank You.
Marek Laszlo
On Fri, Dec 16, 2016 at 2:26 PM, Michal Sojka <sojkam1@fel.cvut.cz> wrote:
Dear students,
as we announced, we have made available 4 boards and motors in room KN:E-2 for you to work at any time. The room is located at Karlovo namesti and is accessible whenever the university is open, which includes even weekends.
The keys from the locker are available at building E reception desk. If the whole room is locked, you can ask the reception guy to open it. Currently, there are only 4 Ethernet cables available in the room - look for yellow cables at the back sides of the room.
The boards will be available in the room today, until 8 PM. Tomorrow, Mr. Hubacek will bring them to H131. Starting from Sunday, the 4 boards will be again in E2. We will temporarily move them to H131 on Wednesdays for exercises.
If you encounter any problems with the boards, motors etc., please let us know immediately so that we can fix the problems quickly.
Best regards, -Michal Sojka
_______________________________________________ PSR mailing list PSR@rtime.felk.cvut.cz https://rtime.felk.cvut.cz/mailman/listinfo/psr
-- Odesláno z mého telefonu pomocí Kaiten Mail. Omluvte prosím mou stručnost.
Hope this copy paste work: U-Boot 1.3.2 (Oct 5 2008 - 00:08:36) CPU: MPC5200B v2.2, Core v1.4 at 396 MHz Bus 132 MHz, IPB 132 MHz, PCI 66 MHz Board: SHARK V1.1 (MIDAM) on a Daughter board I2C: 85 kHz, ready DRAM: 128 MB FLASH: 64 MB In: serial Out: serial Err: serial Net: FEC ETHERNET POST i2c PASSED POST cpu PASSED IDE: Bus 0: not available U-Boot compiled by Michal Hrouda - Energocentrum Plus s.r.o. ;-) Do not forget to setup MAC address (default 00:04:9f:00:27:5f) ! Hit any key to stop autoboot: 0 BOOTP broadcast 1 DHCP client bound to address 192.168.202.51 Using FEC ETHERNET device TFTP from server 192.168.202.4; our IP address is 192.168.202.51 Filename 'vxworks/vxWorks-midam.bin'. Load address: 0x100000 Loading: ################################################################# ################################################################# ################## done Bytes transferred = 2158256 (20eeb0 hex) ## Starting application at 0x00100000 ... Adding 7221 symbols for standalone. ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]] ]]]] ]]]]]]]]]] ]] ]]]] (R) ] ]]]]]]]]] ]]]]]] ]]]]]]]] ]] ]]]] ]] ]]]]]]] ]]]]]]]] ]]]]]] ] ]] ]]]] ]]] ]]]]] ] ]]] ] ]]]] ]]] ]]]]]]]]] ]]]] ]] ]]]] ]] ]]]]] ]]]] ]]] ]] ] ]]] ]] ]]]]] ]]]]]] ]] ]]]]]]] ]]]] ]] ]]]] ]]]]] ] ]]]] ]]]]] ]]]]]]]] ]]]] ]] ]]]] ]]]]]]] ]]]] ]]]]]] ]]]]] ]]]]]] ] ]]]]] ]]]] ]] ]]]] ]]]]]]]] ]]]] ]]]]]]] ]]]]] ] ]]]]]] ] ]]] ]]]] ]] ]]]] ]]]] ]]]] ]]]] ]]]]]]]] ]]]]] ]]] ]]]]]]] ] ]]]]]]] ]]]] ]]]] ]]]] ]]]]] ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]]]]]]]]]]]]]]]]]]]] Development System ]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]]]]]]]]]]]]]]]]]] VxWorks 6.9 ]]]]]]]]]]]]]]]]]]]]]]]]]] KERNEL: WIND version 2.13 ]]]]]]]]]]]]]]]]]]]]]]]]] Copyright Wind River Systems, Inc., 1984-2016 CPU: Freescale Lite5200B - MPC5200B3. Processor #0. Memory Size: 0x7e50000 (~126Mb). BSP version 6.9/0. Created: Nov 29 2016 16:19:59 ED&R Policy Mode: Lab WDB Comm Type: WDB_COMM_NETWORK WDB: Ready. On Fri, Dec 16, 2016 at 7:12 PM, Michal Sojka <sojkam1@fel.cvut.cz> wrote:
What do you see on serial line/usb? Does the board boot VxWorks? 0x100000 is the address where bootloader loads the vxworks image.
On 16. prosince 2016 19:04:20 CET, "Marek L." <laggersvk@gmail.com> wrote:
Good evening,
I am at the KN:E2. The left front computer has some problems with the display.
I am now on right front computer and cant connect to target. It says that there is some error on 0x100000 address. Some midam inconsistency or something like that. Tried it on: 192.168.202.48 192.168.202.51
I also found out that you must probably need to use network mask of 202 at KN:E2.
Where might be problem?
Thank You.
Marek Laszlo
On Fri, Dec 16, 2016 at 2:26 PM, Michal Sojka <sojkam1@fel.cvut.cz> wrote:
Dear students,
as we announced, we have made available 4 boards and motors in room KN:E-2 for you to work at any time. The room is located at Karlovo namesti and is accessible whenever the university is open, which includes even weekends.
The keys from the locker are available at building E reception desk. If the whole room is locked, you can ask the reception guy to open it. Currently, there are only 4 Ethernet cables available in the room - look for yellow cables at the back sides of the room.
The boards will be available in the room today, until 8 PM. Tomorrow, Mr. Hubacek will bring them to H131. Starting from Sunday, the 4 boards will be again in E2. We will temporarily move them to H131 on Wednesdays for exercises.
If you encounter any problems with the boards, motors etc., please let us know immediately so that we can fix the problems quickly.
Best regards, -Michal Sojka
_______________________________________________ PSR mailing list PSR@rtime.felk.cvut.cz https://rtime.felk.cvut.cz/mailman/listinfo/psr
-- Odesláno z mého telefonu pomocí Kaiten Mail. Omluvte prosím mou stručnost.
Please, for obtaining IP address of board use `ifconfig` command. Jiri On 12/16/2016 07:18 PM, Marek L. wrote:
Hope this copy paste work:
U-Boot 1.3.2 (Oct 5 2008 - 00:08:36)
CPU: MPC5200B v2.2, Core v1.4 at 396 MHz Bus 132 MHz, IPB 132 MHz, PCI 66 MHz Board: SHARK V1.1 (MIDAM) on a Daughter board I2C: 85 kHz, ready DRAM: 128 MB FLASH: 64 MB In: serial Out: serial Err: serial Net: FEC ETHERNET POST i2c PASSED POST cpu PASSED IDE: Bus 0: not available
U-Boot compiled by Michal Hrouda - Energocentrum Plus s.r.o. ;-) Do not forget to setup MAC address (default 00:04:9f:00:27:5f) !
Hit any key to stop autoboot: 0 BOOTP broadcast 1 DHCP client bound to address 192.168.202.51 Using FEC ETHERNET device TFTP from server 192.168.202.4; our IP address is 192.168.202.51 Filename 'vxworks/vxWorks-midam.bin'. Load address: 0x100000 Loading: ################################################################# ################################################################# ################## done Bytes transferred = 2158256 (20eeb0 hex) ## Starting application at 0x00100000 ...
Adding 7221 symbols for standalone.
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]] ]]]] ]]]]]]]]]] ]] ]]]] (R) ] ]]]]]]]]] ]]]]]] ]]]]]]]] ]] ]]]] ]] ]]]]]]] ]]]]]]]] ]]]]]] ] ]] ]]]] ]]] ]]]]] ] ]]] ] ]]]] ]]] ]]]]]]]]] ]]]] ]] ]]]] ]] ]]]]] ]]]] ]]] ]] ] ]]] ]] ]]]]] ]]]]]] ]] ]]]]]]] ]]]] ]] ]]]] ]]]]] ] ]]]] ]]]]] ]]]]]]]] ]]]] ]] ]]]] ]]]]]]] ]]]] ]]]]]] ]]]]] ]]]]]] ] ]]]]] ]]]] ]] ]]]] ]]]]]]]] ]]]] ]]]]]]] ]]]]] ] ]]]]]] ] ]]] ]]]] ]] ]]]] ]]]] ]]]] ]]]] ]]]]]]]] ]]]]] ]]] ]]]]]]] ] ]]]]]]] ]]]] ]]]] ]]]] ]]]]] ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]]]]]]]]]]]]]]]]]]]] Development System ]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]]]]]]]]]]]]]]]]]] VxWorks 6.9 ]]]]]]]]]]]]]]]]]]]]]]]]]] KERNEL: WIND version 2.13 ]]]]]]]]]]]]]]]]]]]]]]]]] Copyright Wind River Systems, Inc., 1984-2016
CPU: Freescale Lite5200B - MPC5200B3. Processor #0. Memory Size: 0x7e50000 (~126Mb). BSP version 6.9/0. Created: Nov 29 2016 16:19:59 ED&R Policy Mode: Lab WDB Comm Type: WDB_COMM_NETWORK WDB: Ready.
On Fri, Dec 16, 2016 at 7:12 PM, Michal Sojka <sojkam1@fel.cvut.cz <mailto:sojkam1@fel.cvut.cz>> wrote:
What do you see on serial line/usb? Does the board boot VxWorks? 0x100000 is the address where bootloader loads the vxworks image.
On 16. prosince 2016 19:04:20 CET, "Marek L." <laggersvk@gmail.com <mailto:laggersvk@gmail.com>> wrote:
Good evening,
I am at the KN:E2. The left front computer has some problems with the display.
I am now on right front computer and cant connect to target. It says that there is some error on 0x100000 address. Some midam inconsistency or something like that. Tried it on: 192.168.202.48 192.168.202.51
I also found out that you must probably need to use network mask of 202 at KN:E2.
Where might be problem?
Thank You.
Marek Laszlo
On Fri, Dec 16, 2016 at 2:26 PM, Michal Sojka <sojkam1@fel.cvut.cz <mailto:sojkam1@fel.cvut.cz>> wrote:
Dear students,
as we announced, we have made available 4 boards and motors in room KN:E-2 for you to work at any time. The room is located at Karlovo namesti and is accessible whenever the university is open, which includes even weekends.
The keys from the locker are available at building E reception desk. If the whole room is locked, you can ask the reception guy to open it. Currently, there are only 4 Ethernet cables available in the room - look for yellow cables at the back sides of the room.
The boards will be available in the room today, until 8 PM. Tomorrow, Mr. Hubacek will bring them to H131. Starting from Sunday, the 4 boards will be again in E2. We will temporarily move them to H131 on Wednesdays for exercises.
If you encounter any problems with the boards, motors etc., please let us know immediately so that we can fix the problems quickly.
Best regards, -Michal Sojka
_______________________________________________ PSR mailing list PSR@rtime.felk.cvut.cz <mailto:PSR@rtime.felk.cvut.cz> https://rtime.felk.cvut.cz/mailman/listinfo/psr <https://rtime.felk.cvut.cz/mailman/listinfo/psr>
-- Odesláno z mého telefonu pomocí Kaiten Mail. Omluvte prosím mou stručnost.
_______________________________________________ PSR mailing list PSR@rtime.felk.cvut.cz https://rtime.felk.cvut.cz/mailman/listinfo/psr
Good morning everyone, I have the same troubles with the target connection through WindRiver. Here is the complete error message: Sun Dec 18 12:34:05 2016 Target name is 192.168.202.62 tgtsvr.ex (VxWorks6x_192.168.202.62@k2-102): Sun Dec 18 12:34:05 2016 Wind River Target Server for Workbench 3.3.6 WTX Library version: 4.2.0.112 Tgtsvr core version: 4.2.0.112 Connecting to the target agent ...... succeeded ! Loading plug-in for VxWorks... succeeded. Checking License... OK VxWorks plugin version: 4.2.0.91 Attaching elf OMF reader for PPC CPU family... succeeded. Differences for module "vxWorks-midam" segment's address 0x100000: Offset Target Value Host Value 0x157 0x80 0x60 0x4ae 0xf8 0xe6 0x65a 0x92 0x82 0x91a 0x92 0x82 Stopping dump. Other errors might exist. Error: The systems running on the target and loaded into the target server memory are different. Either wrong core file is selected on the host or text section is corrupted on target side. Error during target server core initialization Warning: Target Server exiting... Does anybody know how to deal with it? Best regards, Maxim Baryshnikov. Quoting "Marek L." <laggersvk@gmail.com>:
Hope this copy paste work:
U-Boot 1.3.2 (Oct 5 2008 - 00:08:36)
CPU: MPC5200B v2.2, Core v1.4 at 396 MHz Bus 132 MHz, IPB 132 MHz, PCI 66 MHz Board: SHARK V1.1 (MIDAM) on a Daughter board I2C: 85 kHz, ready DRAM: 128 MB FLASH: 64 MB In: serial Out: serial Err: serial Net: FEC ETHERNET POST i2c PASSED POST cpu PASSED IDE: Bus 0: not available
U-Boot compiled by Michal Hrouda - Energocentrum Plus s.r.o. ;-) Do not forget to setup MAC address (default 00:04:9f:00:27:5f) !
Hit any key to stop autoboot: 0 BOOTP broadcast 1 DHCP client bound to address 192.168.202.51 Using FEC ETHERNET device TFTP from server 192.168.202.4; our IP address is 192.168.202.51 Filename 'vxworks/vxWorks-midam.bin'. Load address: 0x100000 Loading: ################################################################# ################################################################# ################## done Bytes transferred = 2158256 (20eeb0 hex) ## Starting application at 0x00100000 ...
Adding 7221 symbols for standalone.
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]] ]]]] ]]]]]]]]]] ]] ]]]] (R) ] ]]]]]]]]] ]]]]]] ]]]]]]]] ]] ]]]] ]] ]]]]]]] ]]]]]]]] ]]]]]] ] ]] ]]]] ]]] ]]]]] ] ]]] ] ]]]] ]]] ]]]]]]]]] ]]]] ]] ]]]] ]] ]]]]] ]]]] ]]] ]] ] ]]] ]] ]]]]] ]]]]]] ]] ]]]]]]] ]]]] ]] ]]]] ]]]]] ] ]]]] ]]]]] ]]]]]]]] ]]]] ]] ]]]] ]]]]]]] ]]]] ]]]]]] ]]]]] ]]]]]] ] ]]]]] ]]]] ]] ]]]] ]]]]]]]] ]]]] ]]]]]]] ]]]]] ] ]]]]]] ] ]]] ]]]] ]] ]]]] ]]]] ]]]] ]]]] ]]]]]]]] ]]]]] ]]] ]]]]]]] ] ]]]]]]] ]]]] ]]]] ]]]] ]]]]] ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]]]]]]]]]]]]]]]]]]]] Development System ]]]]]]]]]]]]]]]]]]]]]]]]]]]] ]]]]]]]]]]]]]]]]]]]]]]]]]]] VxWorks 6.9 ]]]]]]]]]]]]]]]]]]]]]]]]]] KERNEL: WIND version 2.13 ]]]]]]]]]]]]]]]]]]]]]]]]] Copyright Wind River Systems, Inc., 1984-2016
CPU: Freescale Lite5200B - MPC5200B3. Processor #0. Memory Size: 0x7e50000 (~126Mb). BSP version 6.9/0. Created: Nov 29 2016 16:19:59 ED&R Policy Mode: Lab WDB Comm Type: WDB_COMM_NETWORK WDB: Ready.
On Fri, Dec 16, 2016 at 7:12 PM, Michal Sojka <sojkam1@fel.cvut.cz> wrote:
What do you see on serial line/usb? Does the board boot VxWorks? 0x100000 is the address where bootloader loads the vxworks image.
On 16. prosince 2016 19:04:20 CET, "Marek L." <laggersvk@gmail.com> wrote:
Good evening,
I am at the KN:E2. The left front computer has some problems with the display.
I am now on right front computer and cant connect to target. It says that there is some error on 0x100000 address. Some midam inconsistency or something like that. Tried it on: 192.168.202.48 192.168.202.51
I also found out that you must probably need to use network mask of 202 at KN:E2.
Where might be problem?
Thank You.
Marek Laszlo
On Fri, Dec 16, 2016 at 2:26 PM, Michal Sojka <sojkam1@fel.cvut.cz> wrote:
Dear students,
as we announced, we have made available 4 boards and motors in room KN:E-2 for you to work at any time. The room is located at Karlovo namesti and is accessible whenever the university is open, which includes even weekends.
The keys from the locker are available at building E reception desk. If the whole room is locked, you can ask the reception guy to open it. Currently, there are only 4 Ethernet cables available in the room - look for yellow cables at the back sides of the room.
The boards will be available in the room today, until 8 PM. Tomorrow, Mr. Hubacek will bring them to H131. Starting from Sunday, the 4 boards will be again in E2. We will temporarily move them to H131 on Wednesdays for exercises.
If you encounter any problems with the boards, motors etc., please let us know immediately so that we can fix the problems quickly.
Best regards, -Michal Sojka
_______________________________________________ PSR mailing list PSR@rtime.felk.cvut.cz https://rtime.felk.cvut.cz/mailman/listinfo/psr
-- Odesláno z mého telefonu pomocí Kaiten Mail. Omluvte prosím mou stručnost.
Yes, thank you. After my re-login, it started to work. Maxim Baryshnikov. Quoting Michal Sojka <sojkam1@fel.cvut.cz>:
On Sun, Dec 18 2016, barysmax@fel.cvut.cz wrote:
Good morning everyone,
I have the same troubles with the target connection through WindRiver. Here is the complete error message:
Can you check whether it works now?
-MS
participants (4)
-
barysmax＠fel.cvut.cz -
jiri hubacek -
Marek L. -
Michal Sojka